Toshiba Tosvert VF-AS1 Instrukcja Użytkownika Strona 179
- Strona / 312
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
E6581301
F-67
6
6.36 Operation panel parameter
6.36.1 Prohibition of key operations and parameter settings
H : Parameter write protect selection
H
: Operation panel frequency setting prohibition selection
H
: Operation panel emergency stop operation prohibition selection
H
: Operation panel reset operation prohibition selection
H
: Prohibition of change of EOQF/HOQF during operation
H
: All key operation prohibition
•
Function
These parameters allow you to prohibit the operation of the RUN and STOP keys on the operation panel
and the change of parameters. Using these parameters, you can also prohibit various key operations.
[Parameter setting]
Title Function Adjustment range Default setting
H Parameter write protect selection :Permit,:Prohibit
H Operation panel frequency setting prohibition selection :Permit,:Prohibit
H
Operation panel emergency stop operation prohibition
selection
:Permit,:Prohibit
H Operation panel reset operation prohibition selection :Permit,:Prohibit
H Prohibition of change of EOQF/HOQF during operation :Permit,:Prohibit
H All key operation prohibition :Permit,:Prohibit
Note: For the setting of H to take effect, the inverter needs to be turned off and turned back on after the
setting.
■ Resetting method
1) Canceling the H prohibition setting
The setting of only parameter H can be changed at any time, even if it is set to .
2) Canceling the H prohibition setting
When this parameter is set to 1 (key operation prohibited), press and hold down the key for 5 seconds or more. The
message WPFQ appears and this setting is canceled temporarily to enable key operation.
To cancel this setting permanently, change the setting of H directly.
ENT
- E6581301Ԙ 1
- I. Safety precautions 3
- Danger 4
- II. Introduction 9
- E6581301 11
- - Contents 11
- 1. Read first 17
- 1.3.1 Names and functions 18
- 1) Outside view 18
- 1.3.2 Detaching the cover 25
- 1.4 Notes on the application 30
- 1.4.1 Motors 30
- 1.4.2 Inverters 32
- ■ Disposal 32
- Warning 33
- 1.4.4 Installation 35
- ■ Installation environment 35
- ■ How to install 36
- 2. Connection equipment 41
- 2.2 Standard connections 43
- 2.3 Description of terminals 48
- 3. Operations 55
- Status monitor mode 56
- Standard monitor mode 56
- (when the power is turned on) 56
- Setting monitor mode 56
- Deceleration 57
- 3.2.2 Panel operation 61
- 4.1 How to set parameters 64
- 5. Basic parameters 67
- CW : Automatic torque boost 69
- ■ Preset speed operation 74
- + The inverter is factory 75
- +To save the frequency 75
- HE and the set 75
- 5.6 Selecting control mode 77
- 2) Decreasing output voltage 78
- 3) Increasing starting torque 78
- 5.8 Base frequency 81
- 5.9 Maximum frequency 82
- Estimation of temperature 90
- 5.17 PWM carrier frequency 96
- Warning 97
- Surge killer 103
- 5.20 Standard default setting 107
- ( ) 109
- 5.22 EASY key function 110
- 6. Extended parameters 113
- 6.2 Input signal selection 115
- Internal command 116
- Servo lock status 120
- Command selected 123
- Operation frequency 125
- 6.8 DC braking 126
- 6.10 Jog run mode 131
- Jumping width 2 135
- Jumping width 1 135
- 6.14.1 Retry function 136
- 6.15 Drooping control 139
- Load portion torque input 141
- 6.20 PID control 145
- 6.22 Setting motor constants 148
- Setting motor constants 150
- 6.24 Torque control 152
- 6.25 Torque limit 154
- Positive torque 155
- Negative torque 155
- • Function 158
- 6.31 Pattern operation 163
- 6.32 Preset speed mode 165
- 6.33 Protection functions 166
- 6.33.3 Emergency stop 167
- H : Emergency stop 167
- 6.34 Override 175
- 6.35 Adjustment parameters 177
- Function 179
- ■ Example of setting 1 181
- ■ Example of setting 2 181
- 6.37 Tracing functions 183
- Trace data 1 184
- Trigger input 184
- 6.38 Communication function 187
- 1) 2-wire RS485 188
- 2) 4-wire RS485 190
- Host computer 191
- 6.39 My function 193
- 6.40 Traverse function 194
- 7.1 External operation 195
- B-contact switch 196
- Input terminal 196
- Inverter 196
- Programmable controller 197
- 7.2.4 Analog input filter 203
- 8.2 Monitoring the status 210
- 8.4.1 Trip code display 216
- 9.1.1 EMC directive 221
- Contact your supplier 222
- Use the 224
- EMC FILTER 226
- Ferrite core 1 227
- Shielded cable or [Note 1] 227
- Noise cut plate 228
- AIC, Fuse and Wire sizes 229
- Ｅ６５８１３００ 232
- Note on wiring 233
- 11. Table of parameters 239
- 12. Specifications 285
- E6581301 286
- ■ Outside dimensions and mass 289
- (Installation dimension) 290
- Before making a service call 295
- Cautions about cleaning 303
- 14.2 Periodical inspection 304
- ■ Check items 304
- 15. Warranty 307
- Warning 309
Powiązane produkty i podręczniki dla Narzędzia Toshiba Tosvert VF-AS1
Narzędzia Toshiba HX7 Instrukcja Użytkownika
(6 strony)
(6 strony)
Narzędzia Toshiba G8000 Instrukcja Użytkownika
(79 strony)
(79 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji